Spiral chute angle

Spiral chute angle 1. Introduction: Chute beneficiation belongs to the slope flow beneficiation process. Mortar is fed to some inclined grooves or slopes, and under the push of water flow, the mineral particle group becomes loose and layered. The upper layer of light minerals quickly flows out of the groove, while the lower layer of minerals with high specific gravity remain inside the groove or are discharged from the bottom at a low speed. After separation and collection, selected minerals and tailings can be obtained. The spiral concentrator is a machine for mining and beneficiation, making it ideal for mining ore in bays, river beds, sand banks, and streams. The equipment has the characteristics of correct structure, simple installation, small land occupation, simple operation, stable beneficiation, clear separation, large processing volume, high efficiency, high beneficiation enrichment ratio, high recycling rate, and reliable operation. It has the advantages of light weight, moisture resistance, rust prevention, corrosion resistance, and strong adaptability to fluctuations in feed volume, concentration, particle size, and grade. 2、 Using a method to set up a spiral concentrator, align it with the vertical line, use an iron frame or wood to fix it in a suitable position, and use a sand pump to transport the ore to the two feeding ports on the spiral head. Add supplementary water, adjust the concentration of the ore slurry, and the ore slurry will naturally swirl from top to bottom. In the flow rate of the inclined plane of the rotation, an inertial centrifugal force will occur, which will cause differences in the gravity, particle size, and shape of the sand ore, Through the influence of the gravity or centrifugal force of the swirling flow, the sand ore is separated, and the selected ore flows into the concentrate hopper and is piped out. The tailings flow into the tailings hopper and are piped to the sand ore pool, and then discharged by a slurry pump, completing the entire beneficiation process. Spiral chute angle 3. Features This equipment is used to separate iron ore, ferrotitanium ore, chromite ore, pyrite ore, zircon ore, Rutile, monazite, phengite, tungsten, tin placer, tantalum ore, niobium ore with a particle size of 0.3-0.02mm and other non-ferrous metal ores, rare mineral metals and non-metallic minerals with gravity differences. This machine also has advantages such as stable sorting process, easy operation, wide range of feeding density, high enrichment ratio, high recovery rate, small area occupation, small water consumption, simple structure, no need for power, large processing capacity, easy installation, simple operation, low investment, and quick effectiveness. The angle of the spiral chute is . The structure of the spiral concentrator consists of six parts: a feeding homogenizer, a feeding chute, a spiral groove, an equipment cutting groove, a product gathering hopper, and a groove bracket (including a cross or triangular frame). The rotating groove connected by spiral blades is a key component. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together by bolts. The spiral groove has a pre made wear-resistant layer on the selected surface. She has the advantages of light weight, strength, durability, and the use of consumables. Above the rotating groove is a multi tube ore feeding homogenizer, which distributes ore evenly and has simple control. The mineral separator is not limited to being placed on a cross (or tripod) on a support table. The uniform slurry is slowly fed to the surface of the rotating groove through the feeding groove installed on the spiral groove head, and sorting is carried out. The tail of the spiral groove is installed in the valve type new product acquisition groove, and the selected new products are divided into three types (or four categories) of new equipment along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that allows the diverse mineral flows obtained to converge and export differently. The cross section of the spiral chute and the different slopes of the curve are particularly suitable for the separation of fine particle materials. 5、 Use This equipment is suitable for separating iron ore, Ilmenite, Chromite, pyrite, zircon sand, Rutile ore, monazite ore, phosphorus, tungsten ore, tin ore, tantalum, tantalum niobium ore and other nonferrous metals, rare mineral metals or nonferrous metal mineral bodies with different specific gravity from fine and small materials with Granularity of 0.3-0.02MM. Spiral chute angle Spiral chute angle