Working method of spiral chute

Working method of spiral chute

The working method of spiral chutes is introduced. Firstly, the separation of minerals by the chute belongs to the inclined flow separation process. The mortar is provided with some inclined grooves or inclined surfaces. Under the push of water flow, the mineral particles are loose and layered, and the lighter minerals in the upper layer quickly discharge out of the groove. The heavy minerals in the lower layer are retained inside the groove or discharged slowly from the lower part. After being collected separately, the concentrate and tailings can be obtained. Spiral chute section. The fiberglass spiral chute is a machine for mining and beneficiation, especially ideal for mining sand in bays, river beds, sandbanks, and streams. The equipment has reasonable structure, simple installation, small footprint, easy operation, stable beneficiation, clear mineral separation, large processing capacity, high efficiency, high beneficiation enrichment ratio, high recovery probability, and reliable operation. There are also advantages such as light weight, moisture resistance, rust prevention, corrosion resistance, and strong applicability to fluctuations in ore feed volume, concentration, particle size, and grade. What is a spiral chute used for? The working method of a spiral chute is 2. Production principle. The screening device of a spiral concentrator is not limited to being placed on the cross (or tripod) of a support table. The average ore slurry is slowly fed to the surface of the rotating groove through the feeding groove installed at the end of the spiral groove head for sorting. The tail end is equipped with a valve block type equipment cutting groove, allowing the sorted products to be divided into three (or four) categories radially according to grade. Change the selection width of each device by adjusting the position of the valve block. The product gathering bucket is a concentric circular tube that gathers and exports the obtained variable mineral flows. The transverse plane of the spiral chute and the slope of the curve vary greatly, making it suitable for the separation of small particle mineral materials. The working method of the spiral chute is three. Characteristics: 1. The sorting step is stable and easy to control. 2. The feeding concentration allows for a large range of different concentrations. 3. High enrichment ratio and recovery rate. 4. It occupies a small area and consumes less water. 5. The structure is simple and does not require power. 6. Large production capacity 7. Easy installation and simple operation 8. Working method of spiral chute with low investment and quick results Spiral chute company. 4. Structural composition of the spiral concentrator consists of 6 parts: feeding homogenizer, feeding chute, spiral groove, equipment cutting groove, product gathering bucket or groove support (including cross or triangular frame), etc. The main component is the rotating groove connected by the rotating disc. The spiral plate is made of fiberglass (fiber reinforced coal gangue) and is bolted together. The sorting surface of the spiral groove has a pre made wear-resistant layer. She has the advantages of lightweight, sturdy, and durable consumables. A multi tube feeding homogenizer is installed above the rotating groove to evenly sort minerals, making control simple and convenient. The mineral screening device is not limited to being placed on a cross (or tripod) on a supporting table. Uniform mineral mortar is slowly fed to the rotating groove surface through the feeding groove installed at the end of the spiral groove head, and selection is carried out. The tail end of the spiral groove is equipped with a valve block type new equipment to obtain the groove. The sorted new products are divided into three (or four) types of new products along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new equipment gathering bucket is a concentric circular tube that allows the intercepted and variable mineral flows to be densely drawn out. The transverse section of the fiberglass chute and the slope change of the curve are extremely suitable for the selection of fine particle materials. 5、 Application. The working method of spiral chute This equipment is suitable for separating iron, ferrotitanium, ferrochrome, ferrosulfide, zircon, Rutile, monazite, phosphate, tungsten ore sand, tin ore, tantalum ore, niobium and other non-ferrous metals, rare mineral metals and non-ferrous metal minerals obtained by gravity difference from fine materials with Granularity of 0.3-0.02mm. Working Method of Spiral Chute Working Method of Spiral Chute

Working method of spiral chute