Do spiral chutes require grooves for selection

Do spiral chutes require grooves for selection

Is it necessary to carve grooves for the selection of spiral chutes? 1. Explanation. Does spiral chute cleaning need grooving? Spiral chute is a combination of the characteristics of spiral concentrator, gravity separation spiral chute, shaking table, gold concentrator centrifuge. After relevant scientific research organized by the Ministry of Metallurgical Industry, and operation appraisal of the design, universities, concentrators and other units, it is considered that this mechanical property is excellent, and the separation goal is improved. It has also won the scientific and technological research achievement award of the Ministry of Metallurgical Industry. It is now widely used in non-ferrous and Ferrous mines. This equipment is used to separate iron ore, ilmenite, chromite, pyrite, zircon, Rutile, monazite, phosphorus, tungsten, tin, tantalum niobium, niobium and other non-ferrous metal ores, rare metals and non-metallic minerals with gravity difference from fine materials with a particle size of 0.3-0.02 mm. 2、 Usage method. The glass fiber reinforced plastic spiral chute shall be erected, the vertical line shall be calibrated, and the iron frame or wood shall be used to fix it in the proper position. The sand pump shall send the ore sand to the two ore feeding ports above the spiral, fill in the water, and adjust the concentration of the ore slurry. The ore slurry will naturally swirl from high to low, and produce a single coherent centrifugal force in the flow speed of the gyrating inclined surface, Through the effect of gravity and centrifugal force obtained through swirling flow, the sand ore is separated, and the concentrate flows into the beneficiation hopper and is connected out through pipelines. The tailings are discharged into the tailings hopper and connected to the sand pit through pipelines, and then discharged by a slurry pump, completing the entire beneficiation process. Do you need to carve grooves for the selection of spiral chutes? 3. Advantages and characteristics: 1. Extremely high efficiency, high recycling rate, and precise beneficiation. Does the spiral chute selection require grooving? 2 No power required; 3. Lightweight, rust proof, durable, wear-resistant, and corrosion-resistant; 4. Low cost operation, long service life; 5 strong adaptability to fluctuations in ore feed volume, concentration, particle size, and grade; The frictional force on the surface of 6 diamond sand makes the beneficiation effect better than other plastic surfaces. Do you need to carve grooves for the selection of spiral chutes. The fiberglass chute is composed of six parts: a feeding homogenizer, a feeding trough, a rotating trough, an equipment cutting trough, a product gathering hopper, and a trough bracket (including a cross or triangular frame). The spiral groove formed by the connection of spiral plates is a key component. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and is bolted together. The selected surface of the rotating groove has a pre designed durable wear-resistant layer. It has the advantages of being lightweight, sturdy, durable, and not easily damaged consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer to divide ore evenly, making it easy to operate. The concentrator is not limited to being placed on the cross (or tripod) of the support table. The evenly divided mineral mortar is slowly fed onto the spiral groove surface through the feeding chute at the head of the rotating groove for sorting. The tail of the rotating groove is installed in a valve type new product selection groove, and the selected new products are divided into three types (or four types) of new equipment along the radial direction according to grade. Change the width of each new product by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that allows the intercepted multi-directional mineral flow to converge and lead out. The cross section of the spiral chute and the different slopes of the curves are very suitable for sorting fine particle materials. 5、 Application field. The spiral chute is suitable for separating fine grained iron ore, ilmenite, chromite, pyrite, placer tin, tantalum niobium ore, gold ore, coal, monazite, Rutile, zircon, rare earth and other metal and nonferrous metal minerals with complete density and specific gravity difference. Do you need to cut grooves for spiral chute selection? Do you need to cut grooves for spiral chute selection

Do spiral chutes require grooves for selection